Brian Chan - Wall-E (CP)

origamimasterjared · December 31st, 2008, 10:56 pm

Ever use ORIPA? You can't just run a CP through ORIPA and BAM M-V distinction. You have to draw the whole CP, in ORIPA, including the mountain-valley distinction. You can then "run" a fully legitimate mountain-valley distinguished CP that you have drawn in ORIPA, through the FOLD button, and it will output what the folded base should look like (give or take a few layers. If you use the Tran-something mode, it will make them all transparent, but will allow you to see how thick it is.)

Mars · Post by **Mars** » December 31st, 2008, 11:07 pm

Ah I'm sorry. It just seemed like what it did (now it seems dumb).
So, I praise you people who take the time draw each line in ORIPA!

I don't have ORIPA though because I can't install anything right now.
Now lets just put this aside, and resume talking about how to fold do Wall-e.

insaneorigami · Post by **insaneorigami** » January 1st, 2009, 10:26 pm

ummmm, where can i download Oripa? I'd really like to have it

Finward · Post by **Finward** » January 1st, 2009, 10:31 pm

I think this link has been posted several times, here is it again
http://mitani.cs.tsukuba.ac.jp/pukiwiki ... n%20Editor
I don't know the link for Java 3D, though.

insaneorigami · Post by **insaneorigami** » January 1st, 2009, 10:41 pm

Ok, so I downloaded the java 3D, but now what do I do? I pressed the "download" button, but it brings me up to this page that has three options, which are: "open, Save, and Cancel" like I'm opening up a file. how do I download?

P.S. I'm sorry if I'm being confusing or anything, its just confusing me a lot, and trying to put it into words.....

barakboom · Post by **barakboom** » January 23rd, 2009, 8:35 pm

yay!!

i did it

(the wall-e)
thanks to everyone, ill upload some photos later.
Actually the Head wasn't hard at all for me. my problem was the wheels

, because i used a tiny paper

.
my wall-e is 7 cm.

insaneorigami · Post by **insaneorigami** » January 23rd, 2009, 8:57 pm

Gratz! I folded one too, but the head looked kinda funky.... anyway, I solved my orpa problem, but havn't gotten around to using it yet. Thanks to everyone who helped

oravannac · Post by **oravannac** » March 9th, 2009, 2:03 am

hi guys
I started the wall-e this afternoon but i'm kinda stuck at how to make the body
i figured out the head and the eyes and i pretty much followed hooodmommy's CP on page 2, also found here : http://www.flickr.com/photos/32648308@N ... 968220709/

how do you guys come to finish up the body of wall-e? the body that i made is really too thin for wall-e

thanks guys

Nepfreak · Post by **Nepfreak** » March 11th, 2009, 1:44 am

someone who folded this, does Wall-E have a back? If he doesn't it would explain why his body would seem thin.

chesslo · Post by **chesslo** » March 11th, 2009, 9:36 am

he doesn't have a back, the body is just a thin paper.

mohit · Post by **mohit** » April 18th, 2009, 6:34 am

guys i dunno wat to do this is quite hard
can any one offer video instructions

WhisperPuffin · Post by **WhisperPuffin** » April 19th, 2009, 9:46 am

Yay!! finished it. 15 x15 cm american foil is too small. one of the eyes is smashed

ftangdude55 · Post by **ftangdude55** » May 30th, 2009, 1:17 am

This is my fold of it. It isn't too good; the body is too big, and the eyes are just terrible. But still. I am glad that i managed to fold it.

chesslo · Post by **chesslo** » May 30th, 2009, 3:00 am

Good try ftangdude55

darkeagle · Post by **darkeagle** » May 30th, 2009, 9:10 pm

I need help in the reference lines